Jump to content
wtf

[SALE] License Plate LED light upgrade, and DIY step by step guide (GT and GTS)

Recommended Posts

[color=#ff0000][size=5][b]NUMBERPLATE LED UPGRADE [/b][/size][/color]

Get rid of the yellow license plate leds! Probably the quickest easiest most obvious mod!

Time required: Should take around 8 minutes or so.


[size=5]To purchase the Upgrade kits, please email [email="[email protected]"][email protected][/email], titled '86FORUMS LICENSE PLATE LED UPGRADE' and we will provide further information.[/size]


Our kits have full Australian Warranties, and we installed them on a local vehicle to verify 100% compatibility. Should anything go wrong with your units, we will exchange straight away, no need to be shipping back overseas.


Disclaimer: THIS INFORMATION IS PURELY FOR INFORMATIONAL PURPOSES ONLY! Street FX takes NO RESPONSIBILITY for any damage or potential damage this alteration may cause. We have tested this to the best of our ability, and it is a VERY straight forward procedure, so we expect no troubles. But if you do something silly and scratch your car in the process, don't blame us!


[img]http://www.streetfx.com.au/galleries/86/diy/platelight_compare.jpg[/img]


Tools & Equipment required:

* 1x Flat blade screwdriver
* 2x Street FX Multidirectional T10 LED Upgrade kits (steer clear of cheap china leds, they flicker and 2-3 of the 5 LEDs will mostly fail within months!)


[size=5]To purchase the Upgrade kits, please email [/size][email="[email protected]"][email protected][/email][size=5], titled '86FORUMS LICENSE PLATE LED UPGRADE' and we will provide further information.[/size]

[size=5][b]BEFORE:[/b][/size]


[img]http://www.streetfx.com.au/galleries/86/diy/platelight_before.jpg[/img]

Procedure:

1) Turn your lights off (otherwise your stock halogen lights will burn your fingers when you try to remove them!)

2) Pop the boot/trunk (interesting side note - the GT model doesnt have a boot release switch on the bootlid like the GTS does!)

3) GTS models have interior trim covering the access for the lights (I didnt realise until we did Cory's car, that the GT model doesn't seem to have this trim)


[img]http://www.streetfx.com.au/galleries/86/diy/platelight1.jpg[/img]


4) Remove the three clips that are circled in red, that secure the upper part of the trim by putting the flat blade screw driver under the clip and twist slightly, the clip will pop open.

[img]http://www.streetfx.com.au/galleries/86/diy/platelight2.jpg[/img]


5) Fold down the upper trim so you have access to the light assembly.

[img]http://www.streetfx.com.au/galleries/86/diy/platelight3.jpg[/img]


6) Hold the bulb holder, and twist to unlock

[img]http://www.streetfx.com.au/galleries/86/diy/platelight4.jpg[/img]

[img]http://www.streetfx.com.au/galleries/86/diy/platelight5.jpg[/img]


6) Remove the bulb holders if you wish to work somewhere with more light (you can do it on the car if you want), and plug in the LEDs. You may need to switch their polarity in the next step.

[img]http://www.streetfx.com.au/galleries/86/diy/platelight6.jpg[/img]


7) Reattach the bulb holders to their loom plug, complete with the new Multi-directional Superbright LEDs. DONT twist lock them back into the bootlid yet. Leave them hanging. The below image shows what I mean, and shows the comparison between stock halogen, and StreetFX LEDs.

[img]http://www.streetfx.com.au/galleries/86/diy/platelight7.jpg[/img]


8) Turn your headlights on and go back to the boot and check both the LEDs are lighting up. If not, unplug the LED from the holder, and turn it 180 degrees to switch polarity. It should now work.


9) Now that both LEDs are working, twist lock the holders into place.

10) Reverse the disassembly process, by locating the plastic clips and pushing them into place.


AFTER:

[img]http://www.streetfx.com.au/galleries/86/diy/platelight_after.jpg[/img]

[img]http://www.streetfx.com.au/galleries/86/diy/platelights_after2.jpg[/img]

[img]http://www.streetfx.com.au/galleries/86/diy/platelights_after3.jpg[/img]

DONE!!!

Share this post


Link to post
Share on other sites
This is rediculously easy to do. Even the rivet things pop out really easily and never felt like I was going to have to force them to come out. Have broken a fair few in my times ha. Would highly recommend it.

Share this post


Link to post
Share on other sites

It is a fairly common T10 connection that is used widely and yes this is a shared part between the Toyota and Subaru so what fits one will fit the other.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...

×
×
  • Create New...